2013-12-29

Thatch Roofing in Miyama-cho, Kyoto Prefecture 茅葺屋根 京都府美山町

 Miyama-cho in northern Kyoto Prefecture is one of the few remaining locations in Japan where the tradition of thatch roofing continues.  Other popular locations are Shirakawago in Gifu Prefecture and Gokayama in Toyama Prefecture.
 Miyama is home to a number of professional roof thatchers, including one of Japan's largest roof thatching companies, Miyama Kayabuki. Another Miyama organization promoting roof thatching in Japan is Kayabukiya.
 This past summer the Miyama Thatch Roof Resource Center was re-thatched by Nishio-san.









ストローベイルセミナーin北海道

木・わら・土の家づくり

日 時: 2014年1月26日(日)10:00~13:00 (終了後の個別相談も可能)
場 所: NPO法人エゾロック 
      札幌市中央区南9条西3丁目1番7号
参加費: 1500円
定 員: 20名

講師  
ワラ : 陣内 雄 (ストローベイル・プランナー、森林活動
土  : 野田 肇介 (野田左官店
建築 : 西條 正幸 (ビオプラス西條デザイン

2014年5月には、上富良野の新築工事でのワークショップも計画しています。
そのときには、実践的に作り方を学べます。
田んぼや野山から材料をとってきて家をつくる。
みんなのチームワークでつくる。
自分たちでできることは自分たちでやる。
 そんな生き方の原点も見つけていけたらと思います。

■セミナー申し込み、問合せ:陣内 jinnn*d2.dion.ne.jp (*の代わりに@を入れてください) まで
更なる詳細はこちらですー>ストローベイル建築そうだん@hokkaido

2013-12-08

Kyoto Imperial Palace

Beautiful










Modifying and Securing Gypsum Mouldings

Using the straight and circular mouldings described in the previous post, the following describes how to cut and secure gypsum mouldings.
 
 Measure the distance of the desired moulding and cut the moulding at a 45 degree angle using a miter box.
 Check cut to ensure a 45 degree angle
Mark finish level with an ink-line
 Check fit of all mouldings, preferably at the same time to ensure clean joints
 
 Treat the back of the mouldings with a sealer to slow the absorption of moisture
 Paint on with brush
 Prepare gypsum based bonding plaster
 Add methylcellulose to improve workability and delay hardening
 Dry mix GL bond and methylcellulose, then add water
 Firmly apply a thin coat of GL Bond, then apply in thick globs
 Wet plaster, firmly apply a thin coat of GL Bond to the base coat, and then set moulding
 First the bottom, then sides
 Lastly, top.
 Check joints
 Adjust joints if needed.
  Set the circular moulding: In this case, equal spacing on sides and top.
 Ensure circular moulding is at the same level as the surrounding mouldings
 Check horizontally and diagonally
  Imperfections can be corrected with paintbrushes and plaster.
 Dip the brush in water and the edge of the gypsum powder, and correct the moulding
 
 After correction
 
 10mm for brown and finish coats

Circular Gypsum Moulding

Modifying the same moulding form from the previous post, the following describes how to create a circular gypsum moulding.
Cut thin metal strips and wrap around a radial handle.
Secure the metal strip: Pierce the metal and handle with a nail, and bend the nail on the opposite side to secure the metal strip.
Punch a hole in the metal strip to allow the radial arm to rotate around a central peg.
Intall the central peg: In this case a nail is pounded into the table and the nail head is cut off with pinchers.
Radial arm and central peg
Determine the desired radius of the circular moulding and attach radial arm.
 Draw outline of circular moulding
 Cut string for circular moulding to improve tensile strength
 Mix gypsum and secure string between moulding outline
 Pull mould form in circular motion
 Repeat
 After completion, remove circular moulding similar to the moulding described in the previous post.